Izdelki za družba epoksi gret (13)

Eine industrielle Bodenbeschichtung, die dank ihrer Epoxidharz-Basis enorm chemikalienbeständig ist. In vielen Farben und den Versionen Säureresistent, Anti-Rutsch, Kalttrocknend, Rapid verfügbar.

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Dymax GA201 forminplace (FIP)/cureinplace (CIP) gasketing resin is formulated for sealing plastic, glass and metal enclosures, and plated surfaces for automotive door handle, appliance housing, and critical electronic assembly and device applications which require a soft, tackfree, flexible gasket. Features: - Cures with UV/Visible light - Moisture resistant - Chemical resistant - Tackfree cure - Soft, durable after complete cure - Conforms to intricate channels and recesses - Compliant with RoHS directives 2015/863/EU

Walk 100×350 jest trampoliną do użytku zewnętrznego, montowana w prosty sposób stabilnie w ziemi. Nasi projektanci zadbali o to aby projekt spełniał najwyższe europejskie standardy. Uzyskaliśmy na nasz produkt certyfikat zgodności z normą PN-EN 1176-1 „Wyposażenie placów zabaw”. Gwarantuje to właściwy poziom bezpieczeństwa podczas zabawy na trampolinie lub wokół niej. Zachęca to jednocześnie do działań i czynności uznanych za korzystne dla dzieci. Trampolina Ziemna mogą użytkowa dzieci w wieku od lat 3 pod nadzorem opiekuna. Dorośli również mogą śmiało sobie poskakać. Walk 100×350 jest gwarancją wspaniałej i bezpiecznej zabawy na powietrzu. Dostępna w szerokim wachlarzu kolorystycznym, pozwalającym dopasować się do każdych oczekiwań. Wykonana jest z najlepszych materiałów, oraz jest bezpieczna dla środowiska naturalnego. Trampolina montowana w ziemi. Trampoliny Ziemne montowane są w ziemi w prosty sposób we wcześniej przygotowanym do tego celu podłożu.

Siliciumcarbid ist stark abrasiv und wird vielfältig im Schleifbereich eingesetzt. Siliciumkarbid ist toxisch unbedenklich, nicht krebserregend und somit gesundheitlich ungefährlich. Besonders gut eignet sich dieses extrem harte Strahlmittel für die Bearbeitung von Materialien mit sehr großer Härte in Injektor- und Druckluftstrahlsystemen. Anwendungsgebiete Reinigungsstrahlen: •Bearbeiten von Werkstücken mit extremer Härte •Reinigen von Metalloberflächen, vor allem bei gehärtetem Stahl •Aufrauhen •Entfernen von Rost und Zunder auf Metallflächen •Mattieren von harten Metallflächen Geeignete Strahlsysteme •Injektorstrahlsysteme •Druckluftstrahlanlagen

Płyty cementowo-wiórowe stosowane są w technologii „suchego montażu”. Dzięki swoim parametrom znajdują zastosowanie w budownictwie, także w elementach konstrukcyjnych. Są odporne na różne warunki atmosferyczne, takie jak mróz czy wilgoć, na działanie pleśni i grzybów, a dzięki zawartości cementu – również odporne na owady. Płyty cementowo-wiórowe to materiał sprężysty - moduł sprężystości płyt wynosi ponad 4500 N/mm2, wytrzymałość na zginanie jest większa niż 9 N/mm2.

It is green colored grease containing high quality base oils with calcium soap. It has a wide range of application areas. It provides quick and effective lubrication in various application areas where operating temperature is not high. • It is recommended to be used in grease lubrication processes of ball and roller bearings and hydraulic turbines, temperatures of which do not exceed 70 °C. • It provides high performance in chassis lubrication processes. • It provides high resistance against water and corrosion. • It reduces abrasions and thus minimizes maintenance costs. • It adheres surfaces, and makes lubrication well due to its fibrous structure, and thus reduces consumption

PUR-CSRIM / Oberflächen lackierbar / gute Temperaturbeständigkeit und Verzugsfreiheit / variable Wanddicken / verschiedenste Bauteil-Geometrien möglich / für leichte und robuste Bauteile

Biological based concrete stain and cement remover for resistant paving and flooring of natural and concrete stone. Fast and reliable removal of concrete-, cement-, lime- and efflorescence stains.

Grout CR Composite , castable, anti-washout, controlled shrinkage cement mortar, superfluid consistency, based on high-resistance cements, superpozzolanic fillers (MICROSIL 90), polymeric modifiers, shrinkage resistant agents, specific additives, calcium silicate mineral fibres, selected silica aggregates. - Based on of thickened silica fume - three-dimensionally reinforced fibre with mineral and synthetic fibres - Provides high adherence and adhesion - dimensionally stable (shrinkage-compensated) - Provides high stability-physical chemical and resistance to chlorides and sulphates - suitable for underwater castings: it is anti-washout - high strength in terms of hydrostatic positive and negative thrust. Repair and protective coatings of hydraulic structures, marine and underwater structures, and articles in critical situations: harsh chemical-physical, leaching water, marine atmosphere, etc. Filling of formwork for the containment of cast immersed in sea water. In case of underwater application, the installation operations must be carried out within 8-10 hours of cleaning and "fouling" (accumulation and deposits of organic and inorganic particles on product surfaces) removal. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour 2/3 of total mixture water in the cement mixer, gradually add the product and the remaining water, until a homogeneous mixture of the required consistency is obtained. For sizable filling thicknesses, greater than 60 mm, Ghiaietto 6.10 (inert washed is selected with a particle size of from 6-10 mm) can be added in a percentage ranging from 20% to 40 %, on the basis of practical requirements. In some particularly demanding cases in terms of the resistance to the "dry-wet" cycle (for example, for the action of the tides) or for chemical attacks particularly strong, it would be advisable to add, in addition to the gravel, even thickened silica fume(MICROSIL 90), and in a variable amount depending on the thickness and construction-related need, to further improve the waterproofing and the mechanical strength of the product. In these cases, please contact our Technical Service. In the case of casts in water, make sure of perfect product hardening before removal of the formwork. Approximately 20,50 kg/m² of Grout CR for every centimetre of thickness to be implemented (approximately 2050 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

Waterbased pigmented primer for all types of masonry substrates. Suitable even on fresh concrete and mortar. Features Excellent adhesion to concrete. Excellent alkali and efflorescence resistance. Excellent water resistance. Good UV resistance. Interior and exterior. Eco friendly. Solvents free. Ready for use, do not dilute.